This commit adds detection and filtering for back-to-back duplicate
getblocks requests. This is needed because the trigger for requesting
more blocks is receiving an orphan. When the peer is further behind than
the number of blocks advertised via a single inventory message, the same
orphan block will be sent multiple times. When the peer receives the
final inventory message, it too contains the orphan that was previously
sent. This leads to a duplicate getblocks request that must be filtered
to prevent requesting the final series of blocks again.
This commit adds environment variable expansion and path cleaning to the
data directory. This allows the user to specify data paths in the config
file such as datadir=~/.btcd/data and datadir=$SOMEVAR/btcd. It also
adds usage instructions and an example to the sample btcd.conf file.
- Remove leftover debug log prints
- Increment waitgroup outside of goroutine
- Various comment and log message consistency
- Combine peer setup and newPeer -> newInboundPeer
- Save and load peers.json to/from cfg.DataDir
- Only claim addrmgr needs more addresses when it has less than 1000
- Add warning if unkown peer on orphan block.
Use it to add multiple peer support. We try and keep 8 outbound peers
active at all times.
This address manager is not as complete as the one in bitcoind yet, but
additional functionality is being worked on.
We currently handle (in a similar manner to bitcoind):
- biasing between new and already tried addresses based on number of connected
peers.
- rejection of non-default ports until desparate
- address selection probabilities based on last successful connection and number
of failures.
- routability checks based on known unroutable subnets.
- only connecting to each network `group' once at any one time.
We currently lack support for:
- tor ``addresses'' (an .onion address encoded in 64 bytes of ip address)
- full state save and restore (we just save a json with the list of known
addresses in it)
- multiple buckets for new and tried addresses selected by a hash of address and
source. The current algorithm functions the same as bitcoind would with only
one bucket for new and tried (making the address cache rather smaller than it
otherwise would be).
The regression test mode is special in that the 'official' block test
suite requires an empty database to work properly. Rather than having to
manual go delete it before each test, add code to automatically delete the
old regression test database when in regression test mode.
This commit modifies the way the data paths are handled. Since there will
ultimately be more data associated with each network than just the block
database, the data path has been modified to be "namespaced" based on the
network. This allows all data associated with a specific network to
simply use the data path without having to worry about conflicts with data
from other networks.
In addition, this commit renames the block database to "blocks" plus a
suffix which denotes the database type. This prevents issues that would
otherwise arise if the user decides to use a different database type and
a file/folder with the same name already eixsts but is of the old database
type. For most users this won't matter, but it does provide nice
properties for testing and development as well since it makes it easy to
go back and forth between database types.
This commit also includes code to upgrade the old database paths to the
new ones so the change is seamless for the user.
Finally, bump the version to 0.2.0.
This commit adds a basic infrastructure to allow upgrades to happen to
btcd as needed. This paves the way for the upcoming data path changes to
be automatically updated for the user as needed and also ensures any
future changes that might require upgrades already have an established
way of performing the needed upgrades.
This change paves the way for saving more than just the block database to
the filesystem (such as address manager data, index data, etc) where the
name "dbdir" no longer makes sense.
This commit changes the code so that all calls to .Add on waitgroups
happen before the associated goroutines are launched. Doing this after
the goroutine could technically cause a race where the goroutine started
and finished before the main goroutine has a chance to increment the
counter. In our particular case none of the goroutines exit quickly
enough for this to be an issue, but nevertheless the correct way should be
used.
This commit adds support for relaying blocks between peers. It keeps
track of inventory that has either already been advertised to remote peers
or advertised by remote peers using a size-limited most recently used
cache. This helps avoid relaying inventory the peer already knows as
much as possible while not allowing rogue peers to eat up arbitrary
amounts of memory with bogus inventory.
improved error handling
Fix testing, no point in running tests multiple times
Fix error when no blocks in database, reopen would misreport NewstSha() return
Rather than sending the root of the an orphan chain when sending an orphan
notification, send the hash of the orphan block itself. The caller can
then call the GetOrphanRoot function with the hash to get the root of the
orphan chain as needed. This is being changed since it's cleaner and more
detministic sending the hash for the orphan block that was just processed
rather than sending a possibly different hash depending on whether there
is an orphan chain or not.
Since the notification channel is provided by the caller and it may or may
not be buffered, send notifications in their own goroutine so the chain
processing code does not have to wait around on the caller to process the
notification before continuing.
This commit reworks the getblocks handling a bit to clean it up and match
the reference implementation handling. In particular, it adds monitoring
for when peers request the final block advertised from a previous
getblocks message and automatically avertises the latest known block
inventory to trigger the peer to send another getblocks message.
When no blocks in the block locator are found, start with the block after
the genesis block. This means the client will start over with the genesis
block if unknown block locators are provided. This mirrors the behavior
in the reference implementation.
This commit reworks the getheaders handling a bit to clean it up and match
the reference implementation handling. In particular, in addition to the
normal handling where headers starting after the block locator up to the
stop hash are served, when no locator hashes are provided, the stop hash
acts as a way to specifically request that header. Next, an empty headers
message is sent when no hashes provided by the block locator can be
found. Finally, there was a bug that was limiting the number of headers
that could requested at once to 500 instead of the expected 2000.
