The getrawtransaction RPC call should return a hex-encoded string of the
transaction when verbose is false instead of a TxRawResult object with the
Hex field set to be compatible with the Sathoshi client. This commit,
along with a recent commit to btcjson corrects this.
Also, while here, do a bit of cleanup, finish a TODO to check for an
invalid hash, and optimize the handling of non-verbose slightly.
The getblock RPC call should return a hex-encoded string of the block when
verbose is false instead of a BlockResult object with a Hex field set to
be compatible with the Sathoshi client. This commit, along with a recent
commit to btcjson corrects this.
Also, while here, move code which only applies to verbose mode after the
call which handles the non-verbose logic. This saves a few cycles since
the non-verbose logic doesn't need the extra information.
This commit adds a new function to btcctl that shows the results as
properly indented JSON instead of relying on spew and changes all of the
commands that used spew to the new function. The output of btcctl
should be more user-facing than developer-facing.
This commit modifies btcctl to show float values with %f instead of the
default %v. This means the values will show similar to 1180923195.260000
instead of 1.18092319526e+09 (scientific notation).
The fee field of the getrawmempool RPC JSON response should be in Bitcoins
instead of Satoshi. This commit corrects that issue.
Also, add a couple of comments and fix a comment typo while here.
Since there is already a variable for the current block height in addition
to the next block height, use the existing curHeight variable instead
doing nextBlockHeight-1 in mempool add.
This commit does some housekeeping on peer.go to make the code more
consistent, correct a few comments, and add new comments to explain the
peer data flow. A couple of examples are variables not using the standard
Go style (camelCase) and comments that don't match the style of other
comments.
Instead of one thread that queues and writes, we move to a two queue
model. The queueHandler muxes all the sources of outgoung packets and
drips them to the actual sender. This is done so that a large send
doesnt' allow the channels to fillup and cause blockmanager and server
to block, which delays other peers.
Most messages we handle as is. However, for getdata we do some manual
limiting and pipelining, we queue up three and then we load the next
into memory, not sending it until the otherp ackets have been sent. We
may want to change this later to queue the packet *then* wait so that we
don't completely drain the pipe.
A few misc tweaks to avoid deadlocking by ensuring the all channels will
always drain. mostly this relates to ensuring that we know no more data
will be coming before we drain the channel, and not queueing after we
are marked to disconnect.
Discussed heavily with drahn@ and davec@.
The regression test does not work properly with the new headers-first
download approach, so force the old inv-based block download for
regression test mode.
It is not necessary to do all of the transaction validation on
blocks if they have been confirmed to be in the block chain leading
up to the final checkpoint in a given blockschain.
This algorithm fetches block headers from the peer, then once it has
established the full blockchain connection, it requests blocks.
Any blocks before the final checkpoint pass true for fastAdd on
btcchain operation, which causes it to do less valiation on the block.
since we don't wait for peers, this largely just waits for the server procs
themselves to die. Unless the entire server is wedged (which is what kill -9 is
for) this should always shut down fairly swiftly.
This should mean we sync addrmanager and disestablish upnp correctly on
interrupt.
Discussed with davec.
This code borrows and fixes up a chunk of code to handle upnp from
Taipei-Torrent (https://github.com/jackpal/Taipei-Torrent), under
current versions of go none of the xml parsing was working correctly.
This fixes that and also refactors the SOAP code to be a little nicer by
stripping off the soap containers. It is still rather rough but seems to
correctly redirect ports and advertise the correct address.
Upnp is not run by default. --upnp will enable it, but it will still not
run if we are not listening or if --externalip is in use.
Closes#51
The you address is the one we already set up fo the user, so either waht
we connected to (this will work with tor, etc), or the ip the user
connect to us from otherwise. We must however check to see if it is the address
of the proxy and strip it.
The me addesss, we use the same address selection for local addresses as
always
This should mean that we pass our tor address out in the version message
and thus the peers should add us to their addressmanager.
This implements only the bare bones of external ip address selection
using very similar algorithms and selection methods to bitcoind. Every
address we bind to, and if we bind to the wildcard, every listening
address is recorded, and one for the appropriate address type of the
peer is selected.
Support for fetching addresses via upnp, external services, or via the
command line are not yet implemented.
Closes#35
Perform the requisite processing on .onion addresses to turn them into the tor
reserved ipv6 region (the same as bitcoind and onioncat). Furthermore,
when printing an ip address, reverse the conversion so we print it
nicely. base32 as standard is uppercase, but tor and bitcoind seem to
use lowercase so we first must for we force .onion addrs to uppercase
(and to lowercase on the reverse).
As a side effect we now should handle dns names on the command line (via tor if
required) and add them to the addressmanger as necessary.
The code to send an address messages in batches was previously clearing
all addresses from the existing message after queueing it to be sent.
Since the message is a pointer, this means it was removing the addresses
from the same message which might not have already been sent yet (from
another goroutine) which led to a race.
This commit modifies the code to create a new address message for each
batch as intended.
Fixes#58.
Updated handleGetRawTransaction to populate all the fields required to
match bitcoind. It still doesn't handle MULTISIG addresses correctly.
Changed handleGetBlock to implement new optional verbose (default true)
flag and also added a verboseTx flag to return TxRawDefault instead of
Txid. When verbose=false, GetBlock returns hex-encoded wire bytes for
the block.
The vout field (as part of the getrawtransaction JSON reply) should be
set to the input's previous outpoint's index, not the current input
index.
Found by flam and reported on IRC. Thanks!
This switches a break to a continue if a txout does not include a
pay-to-pubkey-hash script type. btcwallet only supports
pay-to-pubkey-hash at the moment, and this fixes an issue where a tx
may have an different type of output, as well as pay-to-pubkey-hash,
which may be ignored by the wallet notification code.
Found by dhill.
I previously fixed the duplicate send (before seeing GH issue #54),
but forgot that btcwallet expects a nil reply when rescan has
finished. This adds the final reply back, but replies with nil.
Fixes#54.
