lbrycrd/doc/release-notes.md

(note: this is a temporary file, to be added-to by anybody, and moved to
release-notes at release time)

Notable changes
===============

SSL support for RPC dropped
----------------------------

SSL support for RPC, previously enabled by the option `rpcssl` has been dropped
from both the client and the server. This was done in preparation for removing
the dependency on OpenSSL for the daemon completely.

Trying to use `rpcssl` will result in an error:

    Error: SSL mode for RPC (-rpcssl) is no longer supported.

If you are one of the few people that relies on this feature, a flexible
migration path is to use `stunnel`. This is an utility that can tunnel
arbitrary TCP connections inside SSL. On e.g. Ubuntu it can be installed with:

    sudo apt-get install stunnel4

Then, to tunnel a SSL connection on 28332 to a RPC server bound on localhost on port 18332 do:

    stunnel -d 28332 -r 127.0.0.1:18332 -p stunnel.pem -P ''

It can also be set up system-wide in inetd style.

Another way to re-attain SSL would be to setup a httpd reverse proxy. This solution
would allow the use of different authentication, loadbalancing, on-the-fly compression and
caching. A sample config for apache2 could look like:

    Listen 443

    NameVirtualHost *:443
    <VirtualHost *:443>

    SSLEngine On
    SSLCertificateFile /etc/apache2/ssl/server.crt
    SSLCertificateKeyFile /etc/apache2/ssl/server.key

    <Location /bitcoinrpc>
        ProxyPass http://127.0.0.1:8332/
        ProxyPassReverse http://127.0.0.1:8332/
        # optional enable digest auth
        # AuthType Digest
        # ...

        # optional bypass bitcoind rpc basic auth
        # RequestHeader set Authorization "Basic <hash>"
        # get the <hash> from the shell with: base64 <<< bitcoinrpc:<password>
    </Location>

    # Or, balance the load:
    # ProxyPass / balancer://balancer_cluster_name

    </VirtualHost>

Random-cookie RPC authentication
---------------------------------

When no `-rpcpassword` is specified, the daemon now uses a special 'cookie'
file for authentication. This file is generated with random content when the
daemon starts, and deleted when it exits. Its contents are used as
authentication token. Read access to this file controls who can access through
RPC. By default it is stored in the data directory but its location can be
overridden with the option `-rpccookiefile`.

This is similar to Tor's CookieAuthentication: see
https://www.torproject.org/docs/tor-manual.html.en

This allows running bitcoind without having to do any manual configuration.

Low-level RPC API changes
--------------------------

- Monetary amounts can be provided as strings. This means that for example the
  argument to sendtoaddress can be "0.0001" instead of 0.0001. This can be an
  advantage if a JSON library insists on using a lossy floating point type for
  numbers, which would be dangerous for monetary amounts.

Option parsing behavior
-----------------------

Command line options are now parsed strictly in the order in which they are
specified. It used to be the case that `-X -noX` ends up, unintuitively, with X
set, as `-X` had precedence over `-noX`. This is no longer the case. Like for
other software, the last specified value for an option will hold.

`NODE_BLOOM` service bit
------------------------

Support for the `NODE_BLOOM` service bit, as described in [BIP
111](https://github.com/bitcoin/bips/blob/master/bip-0111.mediawiki), has been
added to the P2P protocol code.

BIP 111 defines a service bit to allow peers to advertise that they support
bloom filters (such as used by SPV clients) explicitly. It also bumps the protocol
version to allow peers to identify old nodes which allow bloom filtering of the
connection despite lacking the new service bit.

In this version, it is only enforced for peers that send protocol versions
`>=70011`. For the next major version it is planned that this restriction will be
removed. It is recommended to update SPV clients to check for the `NODE_BLOOM`
service bit for nodes that report versions newer than 70011.

Any sequence of pushdatas in OP_RETURN outputs now allowed
----------------------------------------------------------

Previously OP_RETURN outputs with a payload were only relayed and mined if they
had a single pushdata. This restriction has been lifted to allow any
combination of data pushes and numeric constant opcodes (OP_1 to OP_16). The
limit on OP_RETURN output size is now applied to the entire serialized
scriptPubKey, 83 bytes by default. (the previous 80 byte default plus three
bytes overhead)

Merkle branches removed from wallet
-----------------------------------

Previously, every wallet transaction stored a Merkle branch to prove its
presence in blocks. This wasn't being used for more than an expensive
sanity check. Since 0.12, these are no longer stored. When loading a
0.12 wallet into an older version, it will automatically rescan to avoid
failed checks.

0.12.0 Change log
=================

Detailed release notes follow. This overview includes changes that affect
behavior, not code moves, refactors and string updates. For convenience in locating
the code changes and accompanying discussion, both the pull request and
git merge commit are mentioned.

### RPC and REST

Asm representations of scriptSig signatures now contain SIGHASH type decodes
----------------------------------------------------------------------------

The `asm` property of each scriptSig now contains the decoded signature hash
type for each signature that provides a valid defined hash type.

The following items contain assembly representations of scriptSig signatures
and are affected by this change:

- RPC `getrawtransaction`
- RPC `decoderawtransaction`
- REST `/rest/tx/` (JSON format)
- REST `/rest/block/` (JSON format when including extended tx details)
- `bitcoin-tx -json`

For example, the `scriptSig.asm` property of a transaction input that
previously showed an assembly representation of:

    304502207fa7a6d1e0ee81132a269ad84e68d695483745cde8b541e3bf630749894e342a022100c1f7ab20e13e22fb95281a870f3dcf38d782e53023ee313d741ad0cfbc0c509001

now shows as:

    304502207fa7a6d1e0ee81132a269ad84e68d695483745cde8b541e3bf630749894e342a022100c1f7ab20e13e22fb95281a870f3dcf38d782e53023ee313d741ad0cfbc0c5090[ALL]

Note that the output of the RPC `decodescript` did not change because it is
configured specifically to process scriptPubKey and not scriptSig scripts.

### Configuration and command-line options

### Block and transaction handling

### P2P protocol and network code

### Validation

### Build system

### Wallet

### GUI

### Tests

### Miscellaneous

- Removed bitrpc.py from contrib

Addition of ZMQ-based Notifications
==================================

Bitcoind can now (optionally) asynchronously notify clients through a
ZMQ-based PUB socket of the arrival of new transactions and blocks.
This feature requires installation of the ZMQ C API library 4.x and
configuring its use through the command line or configuration file.
Please see docs/zmq.md for details of operation.