Break the circular dependency between main and txdb by:
- Moving `CBlockFileInfo` from `main.h` to `chain.h`. I think this makes
sense, as the other block-file stuff is there too.
- Moving `CDiskTxPos` from `main.h` to `txdb.h`. This type seems
specific to txdb.
- Pass a functor `insertBlockIndex` to `LoadBlockIndexGuts`. This leaves
it up to the caller how to insert block indices.
Previously we used the CInv that would be sent to the peer announcing the
transaction as the key, but using the txid instead allows us to decouple the
p2p layer from the application logic (which relies on this map to avoid
duplicate tx requests).
Currently, we're keeping a timeout for each requested block, starting
from when it is requested, with a correction factor for the number of
blocks in the queue.
That's unnecessarily complicated and inaccurate.
As peers process block requests in order, we can make the timeout for each
block start counting only when all previous ones have been received, and
have a correction based on the number of peers, rather than the total number
of blocks.
Two-line patch to make it possible to shut down bitcoind cleanly during
the initial ActivateBestChain.
Fixes#6459 (among other complaints).
To reproduce:
- shutdown bitcoind
- copy chainstate
- start bitcoind
- let the chain sync a bit
- shutdown bitcoind
- copy back old chainstate
- start bitcoind
- bitcoind will catch up with all blocks during Init()
(the `boost::this_thread::interruption_point` / `ShutdownRequested()`
dance is ugly, this should be refactored all over bitcoind at some point
when moving from boost::threads to c++11 threads, but it works...)
The "feefilter" p2p message is used to inform other nodes of your mempool min fee which is the feerate that any new transaction must meet to be accepted to your mempool. This will allow them to filter invs to you according to this feerate.
This implements caching of ancestor state to each mempool entry, similar to
descendant tracking, but also including caching sigops-with-ancestors (as that
metric will be helpful to future code that implements better transaction
selection in CreatenewBlock).
The work limit served to prevent the descendant walking algorithm from doing
too much work by marking the parent transaction as dirty. However to implement
ancestor tracking, it's not possible to similarly mark those descendant
transactions as dirty without having to calculate them to begin with.
This commit removes the work limit altogether. With appropriate
chain limits (-limitdescendantcount) the concern about doing too much
work inside this function should be mitigated.
Continues "Make logging for validation optional" from #6519.
The idea there was to remove all ERROR logging of rejected transaction,
and move it to one message in the class 'mempoolrej' which logs the
state message (and debug info). The superfluous ERRORs in the log
"terrify" users, see for example issue #5794.
Unfortunately a lot of new logging was introduced in #6871 (RBF) and
#7287 (misc refactoring). This pull updates that new code.
SequenceLocks functions are used to evaluate sequence lock times or heights per BIP 68.
The majority of this code is copied from maaku in #6312
Further credit: btcdrak, sipa, NicolasDorier
fad6244 ATMP: make nAbsurdFee const (MarcoFalke)
fa762d0 [wallet.h] Remove main.h include (MarcoFalke)
fa79db2 Move maxTxFee out of mempool (MarcoFalke)
ProcessNewBlock would return failure early if CheckBlock failed, before
calling AcceptBlock. AcceptBlock also calls CheckBlock, and upon failure
would update mapBlockIndex to indicate that a block was failed. By returning
early in ProcessNewBlock, we were not marking blocks that fail a check in
CheckBlock as permanently failed, and thus would continue to re-request and
reprocess them.
Also renames whitelistalwaysrelay.
Nodes relay all transactions from whitelisted peers, this
gets in the way of some useful reasons for whitelisting
peers-- for example, bypassing bandwidth limitations.
The purpose of this forced relaying is for specialized gateway
applications where a node is being used as a P2P connection
filter and multiplexer, but where you don't want it getting
in the way of (re-)broadcast.
This change makes it configurable with whitelistforcerelay.
"permit" is currently used to configure transaction filtering, whereas replacement is more to do with the memory pool state than the transaction itself.
Add a configuration option `-permitrbf` to set transaction replacement policy
for the mempool.
Enabling it will enable (opt-in) RBF, disabling it will refuse all
conflicting transactions.
If a new transaction will cause limitfreerelay
to be exceeded it should not be accepted
into the memory pool and the byte counter
should be updated only after the fact.
After discussion in #7164 I think this is better.
Max tip age was introduced in #5987 to make it possible to run
testnet-in-a-box. But associating this behavior with the testnet chain
is wrong conceptually, as it is not needed in normal usage.
Should aim to make testnet test the software as-is.
Replace it with a (debug) option `-maxtipage`, which can be
specified only in the specific case.
We used to have a trickle node, a node which was chosen in each iteration of
the send loop that was privileged and allowed to send out queued up non-time
critical messages. Since the removal of the fixed sleeps in the network code,
this resulted in fast and attackable treatment of such broadcasts.
This pull request changes the 3 remaining trickle use cases by random delays:
* Local address broadcast (while also removing the the wiping of the seen filter)
* Address relay
* Inv relay (for transactions; blocks are always relayed immediately)
The code is based on older commits by Patrick Strateman.
- Avoids string typos (by making the compiler check)
- Makes it easier to grep for handling/generation of a certain message type
- Refer directly to documentation by following the symbol in IDE
- Move list of valid message types to protocol.cpp:
protocol.cpp is a more appropriate place for this, and having
the array there makes it easier to keep things consistent.
Mempool requests use a fair amount of bandwidth when the mempool is large,
disconnecting peers using them follows the same logic as disconnecting
peers fetching historical blocks.
aa4b0c2 When not filtering blocks, getdata sends more in one test (Pieter Wuille)
d41e44c Actually only use filterInventoryKnown with MSG_TX inventory messages. (Gregory Maxwell)
b6a0da4 Only use filterInventoryKnown with MSG_TX inventory messages. (Patick Strateman)
6b84935 Rename setInventoryKnown filterInventoryKnown (Patick Strateman)
e206724 Remove mruset as it is no longer used. (Gregory Maxwell)
ec73ef3 Replace setInventoryKnown with a rolling bloom filter. (Gregory Maxwell)
One test in AcceptToMemoryPool was to compare a transaction's fee
agains the value returned by GetMinRelayFee. This value was zero for
all small transactions. For larger transactions (between
DEFAULT_BLOCK_PRIORITY_SIZE and MAX_STANDARD_TX_SIZE), this function
was preventing low fee transactions from ever being accepted.
With this function removed, we will now allow transactions in that range
with fees (including modifications via PrioritiseTransaction) below
the minRelayTxFee, provided that they have sufficient priority.
